______________________
| |
"J7" Pin #1 | O O O O O O O O O O | Pin #10
Main Board |_____________________|
| | | | | | | | | |
--- --- | | --- ---
A R U L C F
M Y S S W M
8 8 B B 8 8
8 8
-----------
"J21" Pin #1 | O O O O | Pin #4
Main Board -----------
| | | |
-------
R8
C
o to AM8 (Where the Anode of D44 was)
\\
\\| B 10K 1N914
|------\\/\\/\\/\\/-----|<-----o to R8
/|
to R239 o----|<----/ 2N3904 or Equivalent
D44 E
to R23 & R30 o-----\\/\\/\\/--:----|<----o Anode to CW8
|
R66 :----|<----o Anode to RY8
10K pair 1N914's (add)
to R31 (10K)
^
|
|
___
break
___
| D15
|------------|<----------------o Goes to 8 Volt LSB
Source
|------------|<----------------o Connect to AM8
Source
|
| 1N914 (add)
to R100 (100 Ohms)
C
o 3 1N914's (add)
\\
(Q8) \\| B R31 |--|<-----o to LSB8
Bal/^Bal |---------\\/\\/\\/\\/--|--|<-----o to USB8
switch /| | | |--|<-----o to FM8
for / | |
IC1 o \\ \\
E / /
R29 \\ \\ R30
/ /
| | R's=10K's
___ |
_ o
--
o-||||--->|-o
-- |
X1 \\
/
R64 \\ 1N914 (add)
10K / R65
|-----\\/\\/\\/\\--------------|<------o AM8
___ 220 |
C44 ___ ---|<---o to CW8
47pf |
--- D13
-
AM8 o------\\/\\/\\/\\---------- o-->|-----o to Q20
10K | D26
|________________________| o
Add this o S1
|
FM8 o---->|-------/\\/\\/\\/----o
1N914 | 10K |
AM8 o---->|------- o-->|-----o to Q20
1N914 | D26
o
o S1
|
FM8 o----\\/\\/\\/\\----->|----
10K | D27 |
| |
AM8 o----\\/\\/\\/\\----->|-------o to Q20
10K | D26
|
o
o S1
|
| SOFTWARE | RADIOS |
| KPG-5D | TK-930 TK-931 |
| KPG-6D | TK-705 TK-805 |
| KPG-7D | TK-630 TK-730 TK-830 |
| KPG-11D | TK-230 TK-330 |
| KPG-15D | KDS-10 |
| KPG-16D | TK-430 TK-431 |
| KPG-21D | TKB-720 TKR-720 TKR-820 |
| KPG-23D | TK-250 TK-350 |
| KPG-25DM2 | TK-840 TK-940 TK-941 |
| KPG-26D | TK-353 |
| KPG-27D | TK-260 TK-270 TK-360 TK-370 |
| KPG-29D | TK-760 TK-762 TK-860 TK-862 |
| KPG-31D | TK-255 |
| KPG-35D | TK-480 TK-481 |
| KPG-38D | TK-290 TK-390 |
| KPG-41D | TK-715 |
| KPG-44D | TK-690 TK-790 TK-890 |
| KPG-47D | TKR-830 |
| KPG-48D | TK-2100(K)(K2) TK-3100(K)(K2) TK-3101(K2) |
| KPG-49D | TK-280 TK-380 TK-780 TK-880 |
| KPG-56D | “G” SERIES PORTABLES & MOBILES (260GK, 360GK, 270GK, 370GK, 760(H)GK, 860(H)GK, TK-762(H)GK, TK862(H)GK |
| KPG-79D | TK-7150 TK-8150 |
| KPG-81D | TK-2160 TK-3160 |
| CABLE | RADIOS |
| KPG-4 | TK-705 TK-760 TK-762 TK-860 TK-862 TK-840 TK-930 TK-630 TK-730 TK-830 |
| KPG-14 | KDS-10 KCT-24S KVT-10 VH-C1 |
| KPG-22 | TK-250 TK-350 TK-260 TK-360 TK-353 TK-270 TK-370 TK-2100 TK-3100 TK-2160 TK-430 TK-431 TK-255 TK-715 TK-3160 |
| KPG-36 | TK-280 TK-380 TK-290 TK-2140 TK-480 TK-481 TK-390 TK-3140 |
| KPG-43 | TK-690 TK-790 TK-890 |
| KPG-46 or KPG-4 | TK-780 TK-880 TK-980 TK-981 TKR-830 TK-7150 TK-8150 |
| KPT-50 | TKB-720 TKR-720 TKR-820 |
Build an adjustment jig plug by taking a 2-conductor 3.5 (d) mm (1⁄8″) plug and short the tip to the barrel.
Turn the transceiver’s power OFF.
Connect the JIG plug to the [REMOTE] jack on the rear panel.
While pushing and holding [P.AMP/ATT] and [TUNE/CALL], turn the transceiver power ON.
Enter TX adjustment mode. : Push [F-2 (TX)]
CAUTION: Connect a dummy load to the antenna connectors during the transmitter adjustment.
Pushing [F-2 (TX)] until you see on the display PO MAX (HF)
Adjust the power using the dial (VFO)
Press F4 (SET) to accept.
The same can be done for
PO MAX (50 M)
PO MAX ( 144 M)
PO MAX ( 430 M)
Be careful you risk destroying your radio all adjustments are at your own risk.
]]>